Mode-S Beast:Kit Assembly - Revision history

imported>Beastadmin at 17:43, 10 November 2013

2013-11-10T17:43:53Z

← Older revision		Revision as of 17:43, 10 November 2013
Line 9:		Line 9:
	Please also note that there are some pictures about what to do for the extra miniADSB installation on its own page.		Please also note that there are some pictures about what to do for the extra miniADSB installation on its own page.

	And finally remember that there are also some solder bridges, which we set up for USB operation prior to delivery. If you need others like the Lantronix Xport or the BTM-222 Bluetooth, please read the bottom of the jumpers page.		And finally remember that there are also some solder bridges, which we set up for USB operation prior to delivery. If you need others like the Lantronix Xport or the BTM-222 Bluetooth, please read the bottom of the [[Mode-S_Beast:Solder Jumper Settings\|jumpers page]].


Line 32:		Line 32:
	\|}		\|}

	(*1) Please swap the brown and black wire as shown on the miniADSB page.		(*1) Please swap the brown and black wire as shown on the [[Mode-S_Beast:External miniADSB Connection\|miniADSB page]].

	I decided to deliver an USB cable as well because		I decided to deliver an USB cable as well because
Line 111:		Line 111:
	\|}		\|}

	And finally remember that there are also some solder bridges, which I set up for USB operation prior to delivery. If you need others like the Lantronix Xport or the BTM-222 Bluetooth, please read the bottom of the jumpers page.		And finally remember that there are also some solder bridges, which I set up for USB operation prior to delivery. If you need others like the Lantronix Xport or the BTM-222 Bluetooth, please read the bottom of the [[Mode-S_Beast:Solder Jumper Settings\|jumpers page]].

	''The Mode-S Beast is now ready to be connected and tested.''		''The Mode-S Beast is now ready to be connected and tested.''

imported>Beastadmin at 16:47, 10 November 2013

2013-11-10T16:47:41Z

← Older revision		Revision as of 16:47, 10 November 2013
Line 68:		Line 68:
	{\| class="wikitable"		{\| class="wikitable"
	\|[[File:SMA-outer-2.jpg\|320px\|Mode-S Beast - SMA Connector Gap ]]		\|[[File:SMA-outer-2.jpg\|320px\|Mode-S Beast - SMA Connector Gap ]]
			\|In case that this does not apply, the SMA connector will not have a proper connection to the Mode-S Beast and it will not reach full performance.
			\|-
	\|[[File:KitCompletion-Washer.jpg\|320px\|Mode-S Beast - 6 mm diameter stainless steel washer applied to the inner side of the SMA]]		\|[[File:KitCompletion-Washer.jpg\|320px\|Mode-S Beast - 6 mm diameter stainless steel washer applied to the inner side of the SMA]]
	\|-
	~~\|In case that this does not apply, the SMA connector will not have a proper connection to the Mode-S Beast and it will not reach full performance.~~
	\|On this photo, you see a simple 6 mm diameter stainless steel washer applied to the inner side of the SMA. We found this works quite well, ensuring that the outer connector can nicely become fixed.		\|On this photo, you see a simple 6 mm diameter stainless steel washer applied to the inner side of the SMA. We found this works quite well, ensuring that the outer connector can nicely become fixed.
	\|}		\|}

imported>Beastadmin at 16:46, 10 November 2013

2013-11-10T16:46:56Z

← Older revision		Revision as of 16:46, 10 November 2013
Line 10:		Line 10:

	And finally remember that there are also some solder bridges, which we set up for USB operation prior to delivery. If you need others like the Lantronix Xport or the BTM-222 Bluetooth, please read the bottom of the jumpers page.		And finally remember that there are also some solder bridges, which we set up for USB operation prior to delivery. If you need others like the Lantronix Xport or the BTM-222 Bluetooth, please read the bottom of the jumpers page.


			==What's in the Box==

	The kit contains different parts depending on the version you've ordered:		The kit contains different parts depending on the version you've ordered:

	~~==What's in the Box==~~

	===1 Channel Version===		===1 Channel Version===

imported>Beastadmin at 16:45, 10 November 2013

2013-11-10T16:45:49Z

← Older revision		Revision as of 16:45, 10 November 2013
Line 1:		Line 1:
	==~~How To Complete The Box Kit~~==		==Preliminary Advice==

	<span style="color:red">'''Important note: You are handling sensitive devices here!'''</span>		<span style="color:red">'''Important note: You are handling sensitive devices here!'''</span>
Line 13:		Line 13:
	The kit contains different parts depending on the version you've ordered:		The kit contains different parts depending on the version you've ordered:

	===~~Part List of the~~ 1 Channel Version===		==What's in the Box==

			===1 Channel Version===

	{\| class="wikitable"		{\| class="wikitable"
Line 21:		Line 23:


	===~~Part List of the~~ 2 Channel Version===		===2 Channel Version===

	{\| class="wikitable"		{\| class="wikitable"
Line 35:		Line 37:
	* I did see that cheap or scrappy USB cables decrease the performance. Mind that there were already issues with cheap USB cables.		* I did see that cheap or scrappy USB cables decrease the performance. Mind that there were already issues with cheap USB cables.


			==How To Complete The Box Kit==

	===SMA and the USB Connector===		===SMA and the USB Connector===

imported>Beastadmin at 16:40, 10 November 2013

2013-11-10T16:40:38Z

← Older revision		Revision as of 16:40, 10 November 2013
Line 110:		Line 110:


	===<span style="color:red">Avoid These Things</span>===		==<span style="color:red">Avoid These Things</span>==

	{\| class="wikitable"		{\| class="wikitable"

imported>Beastadmin at 16:35, 10 November 2013

2013-11-10T16:35:56Z

← Older revision		Revision as of 16:35, 10 November 2013
Line 5:		Line 5:
	Ok, let me say they are not so sensitive, lets compare them to standard computer parts. I never destroyed a device at all.		Ok, let me say they are not so sensitive, lets compare them to standard computer parts. I never destroyed a device at all.

	<span style="color:red">Take care on electrostatic discharge, don't user plumber tools</span> and if you have doubts, ask someone in your neighbourhood for help. Completing the kit is not complicated and I need about ~~30min~~ for one. So better take help from someone who knows how to handle these kind of parts instead doing it by yourselfs. If nothing helps and if you are using a directly mains connected soldering iron, disconnect it from the mains each time you solder. Taking care this time is surely worth the result.		<span style="color:red">Take care on electrostatic discharge, don't user plumber tools</span> and if you have doubts, ask someone in your neighbourhood for help. Completing the kit is not complicated and I need about 30 minutes for one. So better take help from someone who knows how to handle these kind of parts instead doing it by yourselfs. If nothing helps and if you are using a directly mains connected soldering iron, disconnect it from the mains each time you solder. Taking care this time is surely worth the result.

	Please also note that there are some pictures about what to do for the extra miniADSB installation on its own page.		Please also note that there are some pictures about what to do for the extra miniADSB installation on its own page.
Line 40:		Line 40:
	{\| class="wikitable"		{\| class="wikitable"
	\|[[File:MeaADSB-conn soldered2.jpg\|320px\|Mode-S Beast - Soldered Connectors]]		\|[[File:MeaADSB-conn soldered2.jpg\|320px\|Mode-S Beast - Soldered Connectors]]
	\|With a good soldering iron, solder the two connectors to the board. On the USB, also solder the two shield pins.<br><br>Do solder all pins of the connector including all ground pins.<br><br>Use the extra SMA hex nut or a simple 6.~~2mm~~ dia stainless steel washer (see below) fully down as distance holder of the front panel.		\|With a good soldering iron, solder the two connectors to the board. On the USB, also solder the two shield pins.<br><br>Do solder all pins of the connector including all ground pins.<br><br>Use the extra SMA hex nut or a simple 6.2 mm dia stainless steel washer (see below) fully down as distance holder of the front panel.
	\|}		\|}

Line 84:		Line 84:
	{\| class="wikitable"		{\| class="wikitable"
	\|[[File:MeaADSB-LEDs-Inserted.jpg\|320px\|Mode-S Beast - LEDs Inserted]]		\|[[File:MeaADSB-LEDs-Inserted.jpg\|320px\|Mode-S Beast - LEDs Inserted]]
	\|Insert the LEDs<br>Start with the blue LED, since this is a little bit larger.<br>Note that here on the photo the right yellow and right green LED are unfortunately swapped...<br>Insert the color scheme:<br>~~1CH~~: green - red - red - green<br>~~2CH~~: green - red - green -red<br>~~4CH~~: red - red - red - red<br>		\|Insert the LEDs<br>Start with the blue LED, since this is a little bit larger.<br>Note that here on the photo the right yellow and right green LED are unfortunately swapped...<br>Insert the color scheme:<br>1 CH: green - red - red - green<br>2 CH: green - red - green -red<br>4 CH: red - red - red - red<br>
	\|-		\|-
	\|[[File:MeaADSB-LEDs-Fixed.jpg\|320px\|Mode-S Beast - LEDs Fixed]]		\|[[File:MeaADSB-LEDs-Fixed.jpg\|320px\|Mode-S Beast - LEDs Fixed]]
Line 120:		Line 120:
	\|}		\|}

	And also mind that the front panel must be mounted in a way that the SMA is higher placed than the ~~USBand~~ the LEDs.		And also mind that the front panel must be mounted in a way that the SMA is higher placed than the USB and the LEDs.

imported>Beastadmin at 16:34, 10 November 2013

2013-11-10T16:34:07Z

@@ Line 36: / Line 36: @@
-===Step 1 - SMA and the USB Connector===
+===SMA and the USB Connector===
 {| class="wikitable"
@@ Line 51: / Line 51: @@
-===Step 2 - Mount the Front Panel===
+===Mount the Front Panel===
 {| class="wikitable"
@@ Line 69: / Line 69: @@
-===Step 3 - Prepare, Insert and Solder LEDs===
+===Prepare, Insert and Solder LEDs===
 {| class="wikitable"
@@ Line 91: / Line 91: @@
 For HW V1.1 (on this photo, visible on the bottom of the PCB), mount the RX screening box.

imported>Beastadmin: Created page with "==How To Complete The Box Kit== '''Important note: You are handling sensitive devices here!''' Ok, let me say they are not so sensitive, lets ..."

2013-11-10T15:59:58Z

Created page with "==How To Complete The Box Kit== '''Important note: You are handling sensitive devices here!''' Ok, let me say they are not so sensitive, lets ..."

New page

==How To Complete The Box Kit==

'''Important note: You are handling sensitive devices here!'''

Ok, let me say they are not so sensitive, lets compare them to standard computer parts. I never destroyed a device at all.

Take care on electrostatic discharge, don't user plumber tools and if you have doubts, ask someone in your neighbourhood for help. Completing the kit is not complicated and I need about 30min for one. So better take help from someone who knows how to handle these kind of parts instead doing it by yourselfs. If nothing helps and if you are using a directly mains connected soldering iron, disconnect it from the mains each time you solder. Taking care this time is surely worth the result.

Please also note that there are some pictures about what to do for the extra miniADSB installation on its own page.

And finally remember that there are also some solder bridges, which we set up for USB operation prior to delivery. If you need others like the Lantronix Xport or the BTM-222 Bluetooth, please read the bottom of the jumpers page.

The kit contains different parts depending on the version you've ordered:

===Part List of the 1 Channel Version===

{| class="wikitable"
|[[File:MeaADSB-1ch-parts.jpg|320px|Mode-S Beast - Parts 1 Channel]]
|1 SMD-preassembled board "Mode-S Beast" 1 right angle female SMA connector 3 green LEDs 2 red LEDs 1 blue LED 1 yellow LED 1 USB Type B female connector 1 high quality USB cable
|}

===Part List of the 2 Channel Version===

{| class="wikitable"
|[[File:MeaADSB-2ch-parts.jpg|320px|Mode-S Beast - Parts 2 Channel]]
|1 SMD-preassembled board "Mode-S Beast" 1 right angle female SMA connector 3 green LEDs 2 red LEDs 1 blue LED 1 yellow LED 33 Ohm standard resistor (not shown) 1 3-pin cable for miniADSB (*1) 1 USB Type B female connector 1 high quality USB cable
|}

(*1) Please swap the brown and black wire as shown on the miniADSB page.

I decided to deliver an USB cable as well because

* some might not have such available and
* I did see that cheap or scrappy USB cables decrease the performance. Mind that there were already issues with cheap USB cables.

===Step 1 - SMA and the USB Connector===

{| class="wikitable"
|[[File:MeaADSB-conn soldered2.jpg|320px|Mode-S Beast - Soldered Connectors]]
|With a good soldering iron, solder the two connectors to the board. On the USB, also solder the two shield pins. Do solder all pins of the connector including all ground pins. Use the extra SMA hex nut or a simple 6.2mm dia stainless steel washer (see below) fully down as distance holder of the front panel.
|}

'''NOTE:''' This showed to be the most critical part for the Mode-S Beast's performance. Use as much heat as possible for the SMA. Wait for the pins to warm up, you cannot destroy something here. I saw SMA connectors that even did not get solder into the pin drills.See two photos below. If you do not burn your finger at the SMA when turing over the board after soldering, it did not get hot enougth.

{| class="wikitable"
|[[File:MeaADSB-2ch-conn soldered1.jpg|320px|Mode-S Beast - Soldered Connectors]]
|For the 2CH device also solder the miniADSB connector and the 33 Ohm resistor.
|}

===Step 2 - Mount the Front Panel===

{| class="wikitable"
|[[File:MeaADSB-front mounted.jpg|320px|Mode-S Beast - Front Panel Mounted]]
|Mount the front panel. Take care that a non-powered USB connector fits. You might test if it fits into the box in order to find out that it needs some left or right shifting. '''Note:''' The front panel has to be mounted in a way that the SMA connector is the highest item of all.
|}

When mounting the front panel, mind that there is a small gap between a mounted SMA connector and the outer locknut, as pointed out here:

{| class="wikitable"
|[[File:SMA-outer-2.jpg|320px|Mode-S Beast - SMA Connector Gap ]]
|[[File:KitCompletion-Washer.jpg|320px|Mode-S Beast - 6 mm diameter stainless steel washer applied to the inner side of the SMA]]
|-
|In case that this does not apply, the SMA connector will not have a proper connection to the Mode-S Beast and it will not reach full performance.
|On this photo, you see a simple 6 mm diameter stainless steel washer applied to the inner side of the SMA. We found this works quite well, ensuring that the outer connector can nicely become fixed.
|}

===Step 3 - Prepare, Insert and Solder LEDs===

{| class="wikitable"
|[[File:MeaADSB-LEDs.jpg|320px|Mode-S Beast Kit Assembly - LEDs]]
|All LEDs do have their cathode to the left side when seen from the front panel. Cathode is the shorter of the two leads of the device.
|-
|[[File:MeaADSB-LED-bending1.jpg|320px|Mode-S Beast Kit Assembly - LED Blending 1]]
|Bend the LEDs using a tool with around 2.5 mm diameter. Mind that the angle should be around 80°. Take again care that the short end is on the left (here: top) side. NOTE: Since a few builds did insert the LEDs the wrong way: the short end is located towards the SMA connector, the long end vice versa towards the USB. This is valid for all LEDs
|-
|[[File:MeaADSB-LED-bending2.jpg|320px|Mode-S Beast Kit Assembly - LED Blending 2]]
|LEDs after bending. As the LEDs are laying here, the short pin on the LEDS shown here is always on top or the right side.
|}

{| class="wikitable"
|[[File:MeaADSB-LEDs-Inserted.jpg|320px|Mode-S Beast - LEDs Inserted]]
|Insert the LEDs Start with the blue LED, since this is a little bit larger. Note that here on the photo the right yellow and right green LED are unfortunately swapped... Insert the color scheme: 1CH: green - red - red - green 2CH: green - red - green -red 4CH: red - red - red - red 
|-
|[[File:MeaADSB-LEDs-Fixed.jpg|320px|Mode-S Beast - LEDs Fixed]]
|Fix the LEDs against the front panel, for example with a wooden stick (I've used a brush stick in the photo). Solder the LEDs and cut the wires. In the background, right hand upper corner, you see the three solder bridges that are necessary for USB RxD, USB TxD and USB RTS. I set them during initial tests and they only need change if you intend to run it via Lantronix Xport or BTM-222 Bluetooth (HW Version 1.0)
|}

For HW V1.1 (on this photo, visible on the bottom of the PCB), mount the RX screening box.