Mode-S Beast:Solder Jumper Settings: Difference between revisions

From Beast Wiki
Jump to navigation Jump to search
imported>Beastadmin
No edit summary
imported>Dl4mea
 
Line 10: Line 10:
'''Note 2:''' For the DIP function control over serial, RxD essentially must be routed to the interface that your application is using to connect the Mode-S Beast.
'''Note 2:''' For the DIP function control over serial, RxD essentially must be routed to the interface that your application is using to connect the Mode-S Beast.


==Solder Jumpers for Hardware Version 1.1==
==Solder Jumpers for Hardware Version 1.1 and later==


This hardware version requires just two solder jumpers, since the outgoing data is routed to all three devices at the same time. USB setting is normally done before shipping.
This hardware version requires just two solder jumpers, since the outgoing data is routed to all three devices at the same time. USB setting is normally done before shipping.
Line 16: Line 16:
[[File:Hwv11-solderjumpers.jpg|400px|Mode-S Beast - Solder Jumpers]]
[[File:Hwv11-solderjumpers.jpg|400px|Mode-S Beast - Solder Jumpers]]


Routing and use of RTS is strongly recommended for the USB interface. With Xport, the RTS can either be disabled completly or the signal has to be re-routed to Xp position as well. Unfortunately the Xport does not have an overload handling of the RTS equal to the USB device, so it is no matter how you do.  
Routing and use of RTS is strongly recommended for the USB interface. With Xport, the RTS can either be disabled completly or the signal has to be re-routed to Xp position as well. Unfortunately the Xport does not have an overload handling of the RTS equal to the USB device, so it is no matter how you do.


==Solder Jumpers for Hardware Version 1.0==
==Solder Jumpers for Hardware Version 1.0==

Latest revision as of 12:37, 30 October 2015

Solder jumpers are used to configure rarely changed functionalities as there are:

  • the interface that you are using towards the PC, named RXD, TXD and RTS
  • the solder jumpers SJ1, SJ2 and SJ3 located below the FPGA are currently not used

Solder jumpers are located on the bottom side of the PCB. The best soldering is done with 1mm solder. It is easier if the PCB is cold, so if you failed several times, let the board cool down.

Note 1: Often users did route RTS to USB and have RTS handshake enabled (IDP#8=ON) while using Xport. Since then the USB is unable to deliver its data, it deactivates RTS and disables the output of the decoder. For this use case, simply disable RTS (DIP#8=open) because the Xport does not provide an overload handling, better than that, I have the impression that the Xport does not get into overload at all.

Note 2: For the DIP function control over serial, RxD essentially must be routed to the interface that your application is using to connect the Mode-S Beast.

Solder Jumpers for Hardware Version 1.1 and later

This hardware version requires just two solder jumpers, since the outgoing data is routed to all three devices at the same time. USB setting is normally done before shipping.

Mode-S Beast - Solder Jumpers

Routing and use of RTS is strongly recommended for the USB interface. With Xport, the RTS can either be disabled completly or the signal has to be re-routed to Xp position as well. Unfortunately the Xport does not have an overload handling of the RTS equal to the USB device, so it is no matter how you do.

Solder Jumpers for Hardware Version 1.0

Mode-S Beast - RS232 solder bridges

RxData on the left, RTS in the center and TxData on the right. The picture shows the full routing of signals for USB, as it is normally done before shipping.

NOTE (1): TX-Data can be routed to all output devices in parallel, so for HW Version 1.1 this jumper block will be removed anyway. But mind NOTE (2)! NOTE (2): If you intend to use Lantronix Xport, the outgoing RxD and TxD are swapped in HW-Version 1.0! That means that the outgoing TxD signal nees to be routed with a wire to the pad in the RxD multiplexer, like shown on this picture:

Mode-S Beast - Hardware version 1.0 - Xport

Wiring of the Mode-S Beast for output using Serial-over-USB and Lantronix Xport at the same time.