Mode-S Beast:Data Input Formats: Difference between revisions
| Line 86: | Line 86: | ||
|'''Function''' | |'''Function''' | ||
|'''OFF = lower case characters''' | |'''OFF = lower case characters''' | ||
|'''ON = upper case characters''' | |'''ON = upper case characters'''<br>'''[Default]''' | ||
|- | |- | ||
|Output Format | |Output Format | ||
| Line 93: | Line 93: | ||
|- | |- | ||
|DF-11/17 only filter | |DF-11/17 only filter | ||
|"d" | |"d": only DF-11 and DF-17 | ||
|"D" | |"D": all known data formats | ||
|- | |- | ||
|Timestamp info (AVR only) | |Timestamp info (AVR only) | ||
|"e" | |"e": enabled | ||
|"E" | |"E": ommitted | ||
|- | |- | ||
|CRC check | |CRC check | ||
Revision as of 14:12, 7 June 2019
The DIP switches are read during startup and taken as a default. Later they can be overwritten by software commands. Anyway, if then a DIP is changed to a position that is different to the pervious settings (by either hardware or software), the new setting takes account.
The software commands are the same in each output mode.
The input format is similar to the binary output format and allows control of DIP#3 until DIP#10 since baudrate setting does not make any sense over a serial interface. All commands start with a sequence
<esc> "1" <esc> is 0x1a, and "1" is 0x31
The next character sets or resets a DIP switch:
Mode-S Beast / Radarcape
| DIP | Bit | Function | OFF, open = lower case characters | ON, closed = upper case characters |
| 1,2 | - | Baudrate | not supported | not supported |
| 3 | 0 | Output Format AVR/Binary | "c" | "C" |
| 4 | 1 | DF-11/17 only filter | "d" | "D" |
| 5 | 2 | MLAT info (AVR only) | "e" | "E" |
| 6 | 3 | CRC check disable | "f" | "F" |
| 7 | 4 | Mode-S Beast classic: DF0/4/5 masking filter |
"g" | "G" |
| 7 | 4 | Radarcape/Mode-S Beast GPS: Legacy 12MHz Timestamp/ GPS Timestamp |
"g" | "G" |
| 8 | 5 | RTS handshake off/on | "h" | "H" |
| 9 | 6 | FEC disable yes/no | "i" | "I" |
| 10 | 7 | Mode-A/C enable on/off | "j" | "J" |
Mode-S Beast Module
| Function | OFF = lower case characters | ON = upper case characters [Default] |
| Output Format | "c": Binary | "C": AVR |
| DF-11/17 only filter | "d": only DF-11 and DF-17 | "D": all known data formats |
| Timestamp info (AVR only) | "e": enabled | "E": ommitted |
| CRC check | "f": disabled | "F": enabled |
| Timestamp Resolution/ |
"g": GPS Timestamp | "G": Legacy 12MHz Timestamp |
| Mode-A/C | "j": on | "J": off |
| User LED Red | "r": on | "R": off |
| User LED Yellow on/off | "y": on | "Y": off |
Mode-S Beast module
- always outputs GPS Timestamp "daysec" part in a range of 0..83999
- Requires RTS input on low TTL for outputting data.
Note: Months after the binary format was introduced, I got noticed that in ASCII <esc> is encoded as 0x1b. I actually wanted to use this code, but unfortunately only implemented my believes. For compatiblity reasons this will now stay as 0x1a and not be changed.
Note: Setting 'g/G' is beeing used for GPS timestamp setting on the Radarcape