Radarcape:Specification: Difference between revisions

From Beast Wiki
Jump to navigation Jump to search
imported>Dl4mea
No edit summary
 
(5 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{#seo:
|title=Radarcape Specification
|titlemode=replace
|keywords=radarcape,specification,hardware,dimensions,weight
|description=Specification of the Radarcape
}}
=Radarcape=
=Radarcape=


* The Radarcape consists of:
* The Radarcape consists of:
** Beaglebone (white) board
** Beaglebone Black SBC computer (earlier version used a Beaglebone White)
** Radarcape Mode-S receiver
** Radarcape Mode-S/ADS-B receiver
** GPS module Trimble Resolution SMT
** GPS module Trimble RES SMT 360 (earlier versions used Resolution SMT and Resolution SMTx)
** Common case
** Device case
* Power Consumption
* Power Consumption
** 5V external supply
** 5 V external supply
** Standard 2.1 mm DC connector (plus inside, minus outside)
** Standard 5.5 mm/ 2.1 mm DC connector (positive inside, negative outside)
** without GPS, operating: typical 620mA
** Electrical current with GPS (including antenna) typical 720 mA
** with GPS (including antenna): typical 720mA
* Dimensions and Weight
* Case
** Length approximately 92 mm (110 mm with antenna connector)
** Length approximately 92 mm (110 mm with antenna connector)
** Width approximately 80 mm
** Width approximately 80 mm
** Height approximately 45 mm
** Height approximately 45 mm
* Weight approximately 0.233 kg
** Weight approximately 0.233 kg


==Linux Distribution==
==Linux Distribution==


The Radarcape operates with Angstrom Embedded Linux, it is using the pure root file system, not a Cloud9 system. Due to that, you may not see internal disk drives when plugging the USB. We do not guarantee stability with other Linux distributions than the one it became delivered, as there were already some issues.
The Radarcape operates an embedded linux distribution. We do not guarantee stability with other Linux distributions than the delivered one.
 
==Beaglebone Board (Rev. A6A)==
 
* AM335x 720MHz ARM Cortex-A8
* 256MB DDR2 RAM
* 3D graphics accelerator (SGX530)
* 2x PRU 32-bit RISC CPUs
* Connectivity
** USB client (mini B receptacle)
** USB host (type A receptacle)
** 100Base-TX Ethernet
** 2x 46 pin headers (used by Radarcape board)
* microSD card with Angstrom Linux distribution
 
More Information: [http://www.beagleboard.org/Products/BeagleBone www.BeagleBoard.org]
 
==Radarcape Board==
 
* FPGA based Mode-S ADS-B receiver
* SMA Mode-S antenna connector
 
==GPS Module==
 
* Trimble Resolution SMT GPS module
* SMB male GPS antenna connector
 
More Information: [http://www.trimble.com/timing/resolution-smt.aspx|Trimble Resolution SMT web page]

Latest revision as of 12:42, 18 November 2019


Radarcape

  • The Radarcape consists of:
    • Beaglebone Black SBC computer (earlier version used a Beaglebone White)
    • Radarcape Mode-S/ADS-B receiver
    • GPS module Trimble RES SMT 360 (earlier versions used Resolution SMT and Resolution SMTx)
    • Device case
  • Power Consumption
    • 5 V external supply
    • Standard 5.5 mm/ 2.1 mm DC connector (positive inside, negative outside)
    • Electrical current with GPS (including antenna) typical 720 mA
  • Dimensions and Weight
    • Length approximately 92 mm (110 mm with antenna connector)
    • Width approximately 80 mm
    • Height approximately 45 mm
    • Weight approximately 0.233 kg

Linux Distribution

The Radarcape operates an embedded linux distribution. We do not guarantee stability with other Linux distributions than the delivered one.

Retrieved from "https://wiki.jetvision.de/index.php?title=Radarcape:Specification&oldid=3472"