Radarcape:Specification: Difference between revisions

From Beast Wiki
Jump to navigation Jump to search
← Older editNewer edit →
imported>Dl4mea
imported>Beastadmin
No edit summary
Line 2: Line 2:


* The Radarcape consists of:
* The Radarcape consists of:
** Beaglebone (white) board
** Beaglebone board
** Radarcape Mode-S receiver
** Radarcape Mode-S/ADS-B receiver
** GPS module Trimble Resolution SMT
** GPS module Trimble Resolution SMTx
** Common case
** Device case
* Power Consumption
* Power Consumption
** 5V external supply
** 5 V external supply
** Standard 2.1 mm DC connector (plus inside, minus outside)
** Standard 5.5 mm/ 2.1 mm DC connector (plus inside, minus outside)
** without GPS, operating: typical 620mA
** Electrical current with GPS (including antenna) typical 720 mA
** with GPS (including antenna): typical 720mA
* Case
* Case
** Length approximately 92 mm (110 mm with antenna connector)
** Length approximately 92 mm (110 mm with antenna connector)
** Width approximately 80 mm
** Width approximately 80 mm
** Height approximately 45 mm
** Height approximately 45 mm
* Weight approximately 0.233 kg
** Weight approximately 0.233 kg


==Linux Distribution==
==Linux Distribution==


The Radarcape operates with Angstrom Embedded Linux, it is using the pure root file system, not a Cloud9 system. Due to that, you may not see internal disk drives when plugging the USB. We do not guarantee stability with other Linux distributions than the one it became delivered, as there were already some issues.
The Radarcape operates an Embedded Linux. We do not guarantee stability with other Linux distributions than the delivered one.


==Beaglebone Board (Rev. A6A)==
==Links==


* AM335x 720MHz ARM Cortex-A8
* [http://www.beagleboard.org/Products/BeagleBone|BeagleBoard.org]
* 256MB DDR2 RAM
* [http://www.trimble.com/timing/resolution-smt.aspx|Trimble Resolution SMT web page]
* 3D graphics accelerator (SGX530)
* 2x PRU 32-bit RISC CPUs
* Connectivity
** USB client (mini B receptacle)
** USB host (type A receptacle)
** 100Base-TX Ethernet
** 2x 46 pin headers (used by Radarcape board)
* microSD card with Angstrom Linux distribution
 
More Information: [http://www.beagleboard.org/Products/BeagleBone www.BeagleBoard.org]
 
==Radarcape Board==
 
* FPGA based Mode-S ADS-B receiver
* SMA Mode-S antenna connector
 
==GPS Module==
 
* Trimble Resolution SMT GPS module
* SMB male GPS antenna connector
 
More Information: [http://www.trimble.com/timing/resolution-smt.aspx|Trimble Resolution SMT web page]

Revision as of 16:20, 19 April 2015

Radarcape

  • The Radarcape consists of:
    • Beaglebone board
    • Radarcape Mode-S/ADS-B receiver
    • GPS module Trimble Resolution SMTx
    • Device case
  • Power Consumption
    • 5 V external supply
    • Standard 5.5 mm/ 2.1 mm DC connector (plus inside, minus outside)
    • Electrical current with GPS (including antenna) typical 720 mA
  • Case
    • Length approximately 92 mm (110 mm with antenna connector)
    • Width approximately 80 mm
    • Height approximately 45 mm
    • Weight approximately 0.233 kg

Linux Distribution

The Radarcape operates an Embedded Linux. We do not guarantee stability with other Linux distributions than the delivered one.

Links

Retrieved from "https://wiki.jetvision.de/index.php?title=Radarcape:Specification&oldid=2524"